Edimax HP-5103K Instrukcja Użytkownika

HP-5103 User Manual 03-2014 / v1.0

9 Step 7 When the following WinPcap Compatibility Assistant appears, select Run the program without getting help.

10 Step 8 After the installation is complete, click “Finish”.

11 Step 9 Click the “Edimax PowerLine Utility”, the “PLC 500Mbps Utility” appears, click “Next” to continue.

12 Step 10 Select where you want to install the utility software, and then click “Next”. Step 11 After the installation is complete, click “Clo

13 Step 12 An icon will appear on your desktop. Click the icon to open the utility software. Note: You can manage all the connected powerline adapt

14 3.2 Win XP/Vista / 7 Step 1 Before installing the utility software, make sure that no other powerline utility is installed on your computer. If a

15 Step 4 If you have not installed WinPcap version 4.1.2 (or higher) on your computer before. The wizard will guide you through the setup process.

16

17 Step 5 When the “Edimax PowerLine Utility” setup wizard appears, click “Next” to continue. Step 6 In the “License Agreement” screen, ple

18 Step 7 Select where you want to install the utility software, and then click “Next”. Step 8 If you confirm to install the utility, click “Next

1 COPYRIGHT Copyright  Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, s

19 Step 9 After the installation is complete, click “Close”. Step 10 An icon will appear on your desktop. Click the icon to open the utility softw

20 Chapter 4: Using the Utility Software 4.1 Main Tab The “Main” tab provides a list of powerline adapters connected to the network. The upper panel

21 4.2 Diagnostics Tab The “Diagnostics” tab displays the system information and history of all remote devices. The upper panel displays technical d

22 4.3 About Tab The “About” tab contains some basic information about the software. You can also enable or disable the autoscan function under “Pr

23 Chapter 5: Group Button This section demonstrates how to add or remove devices from a HomePlug AV network with the “Group” button. 5.1 Forming a

24 5.2 Joining a Network If you want to add a new powerline device to an existing network, follow the following procedures: Step 1 Press the “Group

25 5.3 Leaving a Network & Joining another Network If you want to remove a powerline device from an existing network and add it to another networ

26 Chapter 6: Troubleshooting If your powerline adapters have difficulty communicating with each other, try the following procedures:  Try power c

27 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital d

28 EU Declaration of Conformity English: This equipment is in compliance with the essential requirements and other relevant provisions of Directive

2 Contents Chapter 1: Introduction ...

29

3 Chapter 1: Introduction 1.1 Product Features  Easy plug-n-play setup and 128-bit AES security  Max. powerline speed up to 500Mbps  Backward

4 1.3 Compatibility AV500 powerline devices (HomePlug AV standard) are incompatible and cannot be used with 14Mbps and 85Mbps powerline devices (Ho

5 Chapter 2: Interfaces 2.1 LEDs LED Status Description LAN Green LAN port connected Blinking LAN activity (transferring data) Off LAN port not c

6 2.2 Button Interface Description Ethernet Port This is a Fast Ethernet port for connecting to a computer or other devices with a network port. Gr

7 Chapter 3:Utility Software Installation 3.1 Win 8 Step 1 Before installing the utility software, make sure that no other powerline utility is ins

8 Step 4 Click right button on WinPCap4.1.2 then click “Properties”. Step 5 Click Compatibility tab and check “Run this program in compatibili