Edimax ES-3132RL Instrukcja Użytkownika

User Manual ES-5816PHG Gigabit 16-Port 802.3at PoE Web Smart Switch

6Rear Panel The 3-pronged power plug is placed at the rear panel of the switch right side shown as below. Hardware Installation Set the switch on

7Software Description This part instructs user how to set up and manage the switch through the web user interface. Please follow the description to

8After the user login, the right side of website shows all functions as Fig. 1-2. Figure 1-2 Configuration System System Configuration This page

9 Figure 2-1 ¾ MAC Address: Displays the unique hardware address assigned by manufacturer (default). ¾ S/W Version: Displays the switch’s firmware

10¾ Fallback IP address: Manually assign the IP address that the network is using. The default IP is 192.168.2.1 ¾ Fallback Subnet Mask: Assign the

11¾ Power Saving Mode: Adjusts the power provided to ports based on the length of the cable used to connect to other devices. Only sufficient power

12 Figure 2-3 Aggregation Port trunk allows multiple links to be bundled together and act as a single physical link for increased throughput. It pro

13LACP IEEE 802.3ad Link Aggregation Control Protocol (LACP) increases bandwidth by automatically aggregating several physical links together as a l

14RSTP IEEE 802.1w Rapid Spanning tree protocol (LACP) provides a loop-free network and redundant links to the core network with rapid convergence t

15RSTP Port Configuration ¾ Port: The port ID. It cannot be changed. Aggregations mean any configured trunk group. ¾ Enabled: Click on the tick-box

FCC Warning This Equipment has been tested and found to comply with the limits for a Class-A digital device, pursuant to Part 15 of the FCC rules. The

16and forward it to another remote RADIUS authentication server to verify access rights. The EAP packet from the RADIUS server also contain the auth

17between hosts connected to the switch and multicast routers in the network. When a switch hears an IGMP report from a host for a given multicast g

18¾ Port to Mirror to: The port that will “duplicate” or “mirror” the traffic on the source port. Only incoming packets can be mirrored. Packets wil

19 Figure 2-9-1 QoS Mode: QoS Disabled When the QoS Mode is set to QoS Disabled, the following table is displayed. QoS Mode: 802.1p Packets are pri

20 QoS Mode: DSCP DSCP: Packets are prioritized using the DSCP (Differentiated Services Code Point) value. The Differentiated Services Code Point (D

21 Figure 2-9-5 Filter Configuration There are 3 mode that you can choice for filter configuration: Disabled: this mode is protected from potentia

22PoE (Power over Ethernet) Configuration PoE technology is a system to pass electrical power safely, along with data, on Ethernet cabling. Power i

23Rate Limit Configuration Type of Port: You can define the certain port as Policer and Shaper before you set up the rate limit. No Limit: T

24 Figure 2-12-1 ¾ Enable Rate Limit: Click the check box to enable storm control. ¾ Rate (number of frames per second): The Rate field is set by a

25Monitorning Statistic Overview Statistic Overview for all ports User can mirror traffic from any source port to a target port for real-time anal

IContent Content………………………………………………………………………………….I Introduction……………………………………………………………………………..1 Product Overview……………………………………………………………………………….1 Gene

26 Figure 3-3-1 ¾ Port: The port number. ¾ Port Active: Shows if the port is a member of an active LACP group. ¾ Partner Port Number: A list of the

27RSTP Status RSTP VLAN Bridge Overview Figure 3-4 ¾ Hello Time: Interval (in seconds) at which the root device transmits a configuration message.

28¾ Root ID : The priority and MAC address of the device in the Spanning Tree that this switch has accepted as the root device, and the port connec

29 Figure 3-5 VeriPHY VeriPHY Cable Diagnostics User can perform cable diagnostics for all ports or selected ports to diagnose any cable faults (sho

30The following are some results of the ping command: ¾ Normal response: The normal response occurs in one to ten seconds, depending on network traf

31 Figure 3-7-2 Figure 3-7-3 Maintenance Warm Restart Press Yes button to restart the switch, the reset will be complete when the power lights sto

32 Figure 4-1 Factory Default Forces the switch to restore the original factory settings. To reset the switch, select “Reset to Factory Defaults” fr

33 Figure43-4 Logout The administrator has write access for all parameters governing the onboard agent. User should therefore assign a new administ

34Reset button for the factory default setting Please take the following steps to reset the Web Smart Switch back to the original default: Step 1:

IIDetailed Statistic………………………………………………………………………..26 LACP Status……………………………………………………………………………. 27 RSTP Status……………………………………………………………………………..28 IGMP S

1Introduction Product Overview This switch is a Web Management Switch equipped with 16-ports 10/100/1000BaseT(X) with 4-port gigabit SFP open slots.

2- Multiple Spanning Tree support ( IEEE std 802.1s ) - IGMP, GARP, GMRP, and GVRP support Quality of Service - Programmable multi-layer classi

3Specifications ¾ Standard IEEE 802.3 10BaseT IEEE 802.3u 100BaseTX IEEE 802.ab 1000BaseT IEEE 802.3z 1000BaseSX/LX IEEE 802.3x Flow Control IEEE 80

4Package Contents Before you start to install this switch, please verify your package that contains the following items: z One Switch z One Power Co

5Hardware Description This part primarily presents hardware of the web-smart switch, physical dimensions and functional overview would be described.